1. GENERAL INFORMATION
IMPORTANT: Read this MSDS before handling or disposing of this product, and provide this information to the Employee, customers, and users of this product. This product is covered by the OSHA Hazard Communication Standard and this document has been prepared in accordance with requirements of this standard.
2. HAZARDOUS INGREDIENT INFORMATION
| CAS No. |
Ingredient Name & % |
Source |
Exposure Data |
| | OSHA: |
No Data Available | | | ACGIH: |
0.05 mg/m3 TWA (respirable fraction) |
| | NIOSH: | 0.05 mg/m3 TWA (respirable dust)25 mg/m3 IDLH (cristobalite, tridymite); 50 mg/m3 IDLH (quartz, tripoli) | | | Supplier: | No Data Available | | | OHSA CAN: | 0.1 mg/m3 TWAEV | | | Mexico: | 10 mg/m3 TWA | | 014808-60-7 | Quartz 25-50% by Weight | Brazil: | No Data Available | | | Source |
Health Data |
| | NIOSH: |
Chronic lung disease (silicosis) | | | Source |
Carcinogen Data |
|
|
OSHA: |
Select Carcinogen: Yes |
|
|
NTP: |
Known Carcinogen: Yes; Suspected Carcinogen: Yes |
|
|
IARC |
Group 1: Yes; Group 2A: No; Group 2b: No; Group 3: Yes; Group 4: No |
| CAS No. |
Ingredient Name & % |
Source |
Exposure Data |
| | OSHA: |
No Data Available | | | ACGIH: | No Data Available | | | NIOSH: | No Data Available | | | Supplier: | No Data Available | | | OHSA CAN: | 50 ppm TWAEV; 270 mg/m3 TWAEV | | | Mexico: | No Data Available | | 000108-65-6 |
Propylene glycol monomethyl ether acetate 5-15% by Weight |
Brazil: | No Data Available | | | Source |
Health Data |
| | NIOSH: |
No Data Available | | | Source |
Carcinogen Data |
| | OSHA: |
Select Carcinogen: No | | | NTP: | Known Carcinogen: No; Suspected Carcinogen: No | | | IARC | Group 1: No; Group 2A: No; Group 2b: No; Group 3: No; Group 4: No |
| CAS No. |
Ingredient Name & % |
Source |
Exposure Data |
| | OSHA: |
100 ppm TWA; 435 mg/m3 TWA ppm STEL; 655 mg/m3 STEL |
|---|
| | ACGIH: | 100 ppm TWA 150 ppm STEL |
|---|
| | NIOSH: | 100 ppm TWA; 435 mg/m3 TWA900 IDLH |
|---|
| | Supplier: | No Data Available |
|---|
| | OHSA CAN: | 100 ppm TWA; 435 mg/m3 TWA150 ppm STEV; 650 mg/m3 STEV |
|---|
|
|
Mexico: |
100 ppm TWA; 435 mg/m3 TWA150 ppm STEL; 655 mg/m3 STEL |
| 001330-20-7 |
Xylenes (o-,m-,p-isomers) 1.0-10% by Weight |
Brazil: |
100 ppm; 340 mg/m3 ;skin absorber; medium degree of harm |
|
|
Source |
Health Data |
|
|
NIOSH: |
Central nervous system depressant; respiratory and eyes irritation |
|
|
Source |
Carcinogen Data |
|
|
OSHA: |
Select Carcinogen: No |
|
|
NTP: |
Known Carcinogen: No; Suspected Carcinogen: No |
|
|
IARC |
Group 1: No; Group 2A: No; Group 2b: No; Group 3: Yes; Group 4: No |
| CAS No. |
Ingredient Name & % |
Source |
Exposure Data |
| | OSHA: |
No Data Available | | | ACGIH: | No Data Available | | | NIOSH: | 6 mg/m3 TWA3000 mg/m3 IDLH | | | Supplier: | No Data Available | | | OHSA CAN: | 0.10 mg/m3 TWAEV (designated substance regulation) 0.20 mg/m3 CEV (designated substance regulation) 0.20 mg/m3 TWAEV | | | Mexico: | No Data Available | | 007631-86-9 |
Silica, amorphous 10-25% by Weight |
Brazil: | No Data Available | | | Source |
Health Data |
| | NIOSH: |
No Data Available | | | Source |
Carcinogen Data |
| | OSHA: |
Select Carcinogen: No | | | NTP: | Known Carcinogen: No; Suspected Carcinogen: No | | | IARC | Group 1: No; Group 2A: No; Group 2b: No; Group 3: Yes; Group 4: No |
| CAS No. |
Ingredient Name & % |
Source |
Exposure Data |
|
|
OSHA: |
15 mg/m3 TWA (total dust) |
| | ACGIH: | 10 mg/m3 TWA |
|---|
| | NIOSH: | NIOSH Potential Occupational Carcinogen |
|---|
| | Supplier: | No Data Available |
|---|
| | OHSA CAN: | 10 mg/m3 TWAEV (total dust) |
|---|
| | Mexico: | 10 mg/m3 TWA (nuisance particulate) 20 mg/m3 STEL |
|---|
| 013463-67-7 |
Titanium dioxide 10-25% by Weight | Brazil: | No Data Available | | | Source |
Health Data |
|---|
| | NIOSH: |
Lung tumors in animals |
|---|
| | Source |
Carcinogen Data |
|---|
| | OSHA: |
Select Carcinogen: No |
|---|
| | NTP: | Known Carcinogen: No; Suspected Carcinogen: No |
|---|
| | IARC | Group 1: No; Group 2A: No; Group 2b: No; Group 3: Yes; Group 4: No |
|---|
| CAS No. |
Ingredient Name & % |
Source |
Exposure Data |
| | OSHA: |
No Data Available | | | ACGIH: | No Data Available | | | NIOSH: | No Data Available | | | Supplier: | No Data Available | | | OHSA CAN: | No Data Available | | | Mexico: | No Data Available | | 021645-51-2 |
Aluminum hydroxide 1.0-10% by Weight |
Brazil: | No Data Available | | | Source |
Health Data |
| | NIOSH: |
No Data Available | | | Source |
Carcinogen Data |
| | OSHA: |
Select Carcinogen: No | | | NTP: | Known Carcinogen: No; Suspected Carcinogen: No |
|
|
IARC |
Group 1: No; Group 2A: No; Group 2b: No; Group 3: No; Group 4: No |
| CAS No. |
Ingredient Name & % |
Source |
Exposure Data |
| | OSHA: |
No Data Available | | | ACGIH: | No Data Available | | | NIOSH: | No Data Available | | | Supplier: | No Data Available | | | OHSA CAN: | No Data Available | | | Mexico: | No Data Available | | 052829-07-9 |
Tinuvin 770 (amine light stabilizer) 1.0-10% by Weight |
Brazil: | No Data Available | | | Source |
Health Data |
| | NIOSH: |
No Data Available | | | Source |
Carcinogen Data |
| | OSHA: |
Select Carcinogen: No | | | NTP: | Known Carcinogen: No; Suspected Carcinogen: No | | | IARC | Group 1: No; Group 2A: No; Group 2b: No; Group 3: No; Group 4: No |
| CAS No. |
Ingredient Name & % |
Source |
Exposure Data |
| | OSHA: |
No Data Available | | | ACGIH: | No Data Available | | | NIOSH: | No Data Available | | | Supplier: | No Data Available | | | OHSA CAN: | No Data Available | | | Mexico: | No Data Available | | 064742-95-6 | Petroleum naphtha, light aromatic 1.0-10% by Weight | Brazil: | No Data Available | | | Source |
Health Data |
|
|
NIOSH: |
No Data Available |
|
|
Source |
Carcinogen Data |
|
|
OSHA: |
Select Carcinogen: No |
|
|
NTP: |
Known Carcinogen: No; Suspected Carcinogen: No |
|
|
IARC |
Group 1: No; Group 2A: No; Group 2b: No; Group 3: No; Group 4: No |
3. HAZARD IDENTIFICATION
Overview: |
NOTICE: Reports have associated repeated and prolonged occupational overexposure to solvents with permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents may be harmful or fatal. Avoid contact with eyes, skin and clothing. Contains 1,2,4Trimethylbenzene, which can cause central nervous system depression, anemia and bronchitis. |
Inhalation: |
May be harmful or fatal if inhaled. Causes nose and throat irritation. Vapors may affect the brain or nervous system causing dizziness, headache or nausea. |
Eyes: |
Causes eye burns. Do not get in eyes. |
Skin: |
Causes skin irritation. May be harmful if absorbed through the skin. |
Ingestion: |
Harmful if swallowed. May cause abdominal pain, nausea, vomiting, diarrhea, or drowsiness. |
Chronic Effects: |
Contains an ingredient which can cause organ damage (See Section 2 and Section 15 for each ingredient). Possible cancer hazard. Contains an ingredient which may cause cancer based on animal data (See Section 2 and Section 15 for each ingredient). Risk of cancer depends on duration and level of exposure |
HMIS Rating: |
Health: 2 Flammability: 2 Reactivity: 0 |
4. FIRST AID MEASURES
| General: |
Remove contaminated clothing and shoes. Get medical attention immediately. Wash clothing before reuse. Thoroughly clean or destroy contaminated shoes. |
| Inhalation: |
If inhaled, remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen.Get medical attention immediately. |
| Eyes: |
In case of contact, immediately flush eyes with plenty of water for at least 15 minutes. Get medical attentionimmediately.. |
| Skin: |
In case of contact, immediately flush skin with soap and plenty of water. Get medical attention immediately |
| Ingestion: |
If swallowed, immediately contact Poison Control Center at 1-800-854-6813. DO NOT induce vomiting unless instructed to do so by medical personnel. Never give anything by mouth to an unconscious person. |
5. PROTECTIVE EQUIPMENT AND CONTROL MEASURES
| Respiratory: |
Select equipment to provide protection from the ingredients listed in Section 2 of this document. Ensure freshair entry during application and drying. If you experience eye watering, headache or dizziness or if air monitoring demonstrates dust, vapor, or mist levels are above applicable limits, wear an appropriate, properly fitted respirator (NIOSH approved) during and after application. Follow respirator manufacturer's directions for respirator use. |
| Eyes: |
Do not get in eyes. Protective equipment should be selected to provide protection from exposure to the chemicals listed in Section 2 of this document. Depending on the site-specific conditions of use, safety glasses, chemical goggles, and/or head and face protection may be required to prevent contact. The equipment must be thoroughly cleaned, or discarded after each use. |
| Skin/Hand: |
Protective equipment should be selected to provide protection from exposure to the chemicals listed in Section 2 of this document. Depending on the site-specific conditions of use, protective gloves, apron, boots,head and face protection may be required to prevent contact. The equipment must be thoroughly cleaned, or discarded after each use. |
| Engineering Controls: |
Prevent build-up of vapors by opening all windows and doors to achieve cross-ventilation. |
| Other Work Practices: |
Emergency eye wash fountains and safety showers should be available in the immediate vicinity of any potential exposure. Use good personal hygiene practices. Wash hands before eating, drinking, using toilet facilities, etc., Promptly remove soiled clothing and wash clothing thoroughly before reuse. Shower after work using plenty of soap and water. |
6. FIRE AND EXPLOSION INFORMATION
| Flash Point: |
F: 114 C: 46 |
| Lower Explosive Limit (LEL): |
1 (%vol in air) at Normal Atmospheric Temp and Pressure |
| Fire and Explosion Hazards: |
Combustible liquid and vapor. FLAMMABLE/COMBUSTIBLE MATERIALS: Will be easily ignited by heat, sparks or flames. Vapors may form explosive mixtures with air. Vapors may travel to source of ignition and flash back. Most vapors are heavier than air. They will spread along ground and collect in low or confinedareas (sewers, basements, tanks) creating a vapor explosion hazard. Runoff to sewers may create fire or explosion hazard. Containers may explode when heated. |
| Fire Fighting Procedures: |
Also Reference Emergency Response Guide Number: Not Determined |
7. PHYSICAL AND CHEMICAL PROPERTIES
| Physical State: |
Liquid |
| pH: |
Not Determined |
| Specific Gravity: |
1.68 |
| Boiling Point (F): |
295 |
| Vapor Density: |
Heavier than air |
| VOC Content (lbs): |
Refer to the Technical Data Sheet for this product |
| Evaporation Rate: |
Slower than ether |
8. STABILITY AND REACTIVITY DATA
| General: |
This product is stable and hazardous polymerization will not occur |
| Incompatible Materials: |
Strong oxidizing agents. |
| Hazardous Decompostion: |
May produce hazardous fumes when heated to decomposition as in welding. Fumes may produce Carbon Dioxide and Carbon Monoxide. |
9. HANDLING AND STORAGE
| Storage Temperature: |
Store between 32 and 120 F |
| Handling and Storage Precautions: |
Keep away from heat, sparks and flame. Do not smoke. Extinguish all flames and pilot lights, and turn off stoves, heaters, electric motors and other sources of ignition during use and until all vapors are gone. Vapors may cause flash fire or ignite explosively. Prevent build-up of vapors by opening all windows and doors to achieve cross-ventilation. Do not get in eyes, on skin or clothing. Close container after each use.Wash thoroughly after handling. |
10. TOXICOLOGICAL DATA
General: |
NOTICE: Reports have associated repeated and prolonged occupational overexposure to solvents with permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents may be harmful or fatal. No additional information provided for this product. See Section 2 for chemical specific data. |
11. ECOLOGICAL DATA
| General: |
No additional information provided for this product. See Section 2 for chemical specific data. |
12. ACCIDENTAL RELEASE MEASURES
|
Spill Response Procedures:
|
ELIMINATE ALL IGNITION SOURCES (no smoking, flares, sparks or flames in immediate area). Use only non-sparking equipment to handle spilled material and absorbent. Do not touch or walkthrough spilled material. Stop leak if you can do so without risk. Prevent entry into waterways sewers, basements or confined areas. A vapor suppressing foam may be used to reduce vapors. Absorb or cover with dry earth, sand, or other non-combustible material and transfer to containers. Use non-sparking tools to collect absorbed material. No additional information provided for this product. See Section 2 for chemical specific data. |
| Public Safety: |
Isolate spill or leak area immediately for at least 25 to 50 meters (80 to 160 feet) in all directions. Keep unauthorized personnel away. Stay upwind. Keep out of low areas. Ventilate closed spaces before entering. LARGE SPILLS: Consider initial downwind evacuation for at least 300 meters (1000 feet). Also, Reference Emergency Response Guide Number: Not Determined |
13. DISPOSAL CONSIDERATION
| Waste Disposal: |
Dispose of in accordance with local, state and federal regulations. (Also reference RCRA information in Section 15 if listed). |
14. REGULATORY INFORMATION
| Regulatory Overview: |
The regulatory data in Section 15 is not intended to be all-inclusive, only selected regulations are represented. All ingredients of this product are listed on the TSCA (Toxic Substance Control Act) Inventory or are not required to be listed on the TSCA Inventory. |
| WHMIS Classification: |
E; B3 |
| Regulatory ListDOT Marine Pollutants (10%): (No Product Ingredients Listed) |
Product Ingredients on List | | DOT Severe Marine Pollutants (1%): (No Product Ingredients Listed) |
| | EPCRA 311/312 Chemicals and RQs: |
| | 000108-65-6 |
Propylene glycol monomethyl ether acetate : (Includes mono- and di- ethers of ethylene glycol; diethylene glycol and triethylene glycol R-(OCH2CH2)n-OR" where n = 1 2 or 3; R = alkyl or aryl groups; R" = R h or groups which when removed yield glycol ethers with the structure R-(OCH2CH2)n-OH. Polymers are excluded from glycol category); Statutory RQ = 1 pound (.454 kg); no final RQ is being assigned to the generic or broad class | | 001330-20-7 |
Xylenes (o-, m-, p- isomers): final RQ = 100 pounds (45.4 kg) | | EPCRA 302 Extremely Hazardous: |
| | (No Product Ingredients Listed) EPCRA313 Toxic Chemicals: |
| 000108-65-6
014808-60-7
001330-20-7
|
Propylene glycol monomethyl ether acetate Quartz Xylenes (o-, m-, p- isomers) | | Mass RTK Substances: |
| 014808-60-7
007631-86-9
013463-67-7
001330-20-7
|
Quartz Silica, amorphous Titanium dioxide Xylenes (o-, m-, p- isomers) | | Mass Extraordinarily Haz Substances: |
| | (No Product Ingredients Listed) Penn RTK Substances: |
|
000108-65-6
014808-60-7
007631-86-9
013463-67-7
001330-20-7 |
Propylene glycol monomethyl ether acetate Quartz Silica, amorphousTitanium dioxide Xylenes (o-, m-, p- isomers) |
| Penn Special Hazardous Substances: (NoProduct Ingredients Listed) |
|
| Rhode Island Hazardous Substances: |
|
013463-67-7
001330-20-7 |
Titanium dioxide Xylenes (o-, m-, p- isomers) |
| RCRA Status: (No Product Ingredients Listed) |
|
| N.J. RTK Substances: |
|
014808-60-7
007631-86-9
013463-67-7
001330-20-7 |
Quartz Silica, amorphous Titanium dioxide Xylenes (o-, m-, p- isomers) |
| N.J. Special Hazardous Substances |
|
| 001330-20-7 |
Xylenes (o-, m-, p- isomers) |
| N.J. Env. Hazardous Substances |
|
000108-65-6
014808-60-7
001330-20-7 |
Propylene glycol monomethyl ether acetateQuartz Xylenes (o-, m-, p- isomers) |
Proposition 65 - Carcinogens:
(No Product Ingredients Listed)
Proposition 65 - Female Reproductive Toxins:
(No Product Ingredients Listed)
Proposition 65 - Male Reproductive Toxins:
(No Product Ingredients Listed)
Proposition 65 - Developmental Toxins:
(No Product Ingredients Listed) |
|
15. OTHER INFORMATION
The information and recommendations contained herein are based upon data believed to be correct. However, no guarantee or warranty of any kind, expressed or implied, is made with respect to the information contained herein. We accept no responsibility and disclaim all liability for any harmful effects, which may be caused by exposure to our products. Customers/users of this product must comply with all applicable health and safety laws, regulations, and orders. |
